TS&CC upcoming events

Volunteer: Mast Crane Operator (May 02, 2026)

Sat, 02 May 2026 13:30:00 GMT

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 02, 2026)

Sat, 02 May 2026 16:30:00 GMT

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 02, 2026)

Sat, 02 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 03, 2026)

Sun, 03 May 2026 13:30:00 GMT

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 03, 2026)

Sun, 03 May 2026 16:30:00 GMT

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 03, 2026)

Sun, 03 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 04, 2026)

Mon, 04 May 2026 21:30:00 GMT

Mast Raising Session (May 04, 2026)

Mon, 04 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 04, 2026)

Mon, 04 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 05, 2026)

Tue, 05 May 2026 21:30:00 GMT

Mast Raising Session (May 05, 2026)

Tue, 05 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 05, 2026)

Tue, 05 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 06, 2026)

Wed, 06 May 2026 21:30:00 GMT

Mast Raising Session (May 06, 2026)

Wed, 06 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 06, 2026)

Wed, 06 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 07, 2026)

Thu, 07 May 2026 21:30:00 GMT

Mast Raising Session (May 07, 2026)

Thu, 07 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 07, 2026)

Thu, 07 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 08, 2026)

Fri, 08 May 2026 21:30:00 GMT

Mast Raising Session (May 08, 2026)

Fri, 08 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 08, 2026)

Fri, 08 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 09, 2026)

Sat, 09 May 2026 13:30:00 GMT

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 09, 2026)

Sat, 09 May 2026 16:30:00 GMT

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 09, 2026)

Sat, 09 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 10, 2026)

Sun, 10 May 2026 13:30:00 GMT

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 10, 2026)

Sun, 10 May 2026 16:30:00 GMT

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 10, 2026)

Sun, 10 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 11, 2026)

Mon, 11 May 2026 21:30:00 GMT

Mast Raising Session (May 11, 2026)

Mon, 11 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 11, 2026)

Mon, 11 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 12, 2026)

Tue, 12 May 2026 21:30:00 GMT

Mast Raising Session (May 12, 2026)

Tue, 12 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 12, 2026)

Tue, 12 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 13, 2026)

Wed, 13 May 2026 21:30:00 GMT

Mast Raising Session (May 13, 2026)

Wed, 13 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 13, 2026)

Wed, 13 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 14, 2026)

Thu, 14 May 2026 21:30:00 GMT

Mast Raising Session (May 14, 2026)

Thu, 14 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 14, 2026)

Thu, 14 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 15, 2026)

Fri, 15 May 2026 21:30:00 GMT

Mast Raising Session (May 15, 2026)

Fri, 15 May 2026 21:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 15, 2026)

Fri, 15 May 2026 22:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Annual Ice-Breaker Regatta (May 16, 2026)

Sat, 16 May 2026 04:00:00 GMT

The 55th annual Ice-Breaker Regatta will take place on the weekend of May 16-17th, 2026. More details to follow. Go to our Icebreaker Regatta page for details about registration for this event.

Volunteer: Mast Crane Operator (May 16, 2026)

Sat, 16 May 2026 13:30:00 GMT

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 16, 2026)

Sat, 16 May 2026 16:30:00 GMT

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 16, 2026)

Sat, 16 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 17, 2026)

Sun, 17 May 2026 13:30:00 GMT

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 13:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 14:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 15:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 15:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Volunteer: Mast Crane Operator (May 17, 2026)

Sun, 17 May 2026 16:30:00 GMT

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 16:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 17:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 18:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 18:45:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 19:30:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 20:15:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Mast Raising Session (May 17, 2026)

Sun, 17 May 2026 21:00:00 GMT

New Process for Mast Stepping

For the safety of all people involved, and in order to make the process of raising masts more efficient, the Board has put in place a new system for use of the Mast Crane.

A certified mast crane officer must be present to unlock and operate the crane. The club will coordinate having an officer present for each scheduled event.

When you register for as session, you will need to provide the names of two people who will accompany you. If you do not have two people with you, it will not be possible to step your mast.

Here is a readiness checklist for stepping your mast:

My motor has been installed and tested and my gas tank is onboard my boat
My mast has been located
Any hardware for mast top (i.e. wind vane) is ready to be installed and is on boat
Any hardware required for mast stepping (thru-bolts, nuts, washers, rubber mast sleeve) are accessible and on boat
All turnbuckles have been fastened to chain plates or mast and appropriately loosened.
Each turnbuckle is outfitted with two pins and two snap rings
The following tools are on my boat: flat-head screwdriver, Philips screwdriver, adjustable wrench and/or wrenches that fit turnbuckle nuts, vice-grip
Mast has been inspected and all stays are in place and kink-free
Spreaders are on board (with fastening screws and nuts)
2 dock lines are fastened and ready for use at dock
2 bumpers are hanging off either side of boat (note that water level is much higher than in fall)

Dinghy Moves to Upper/Center Lot (May 19, 2026)

Tue, 19 May 2026 19:00:00 GMT

Moving Member Dinghies from north lot to upper center lot.

Dinghies stored offsite (new and current dinghy members) for the winter can be brought on site starting Tuesday, May 19th.

Please wear appropriate footwear and bring work gloves if you have them.

Toronto International Outrigger Challenge (TIOC) (September 19, 2026)

Sat, 19 Sep 2026 11:30:00 GMT

TIOC is a terrific day of competitive racing and fun. Based out of the Toronto Sailing & Canoe Club (TS&CC), this popular event challenges an international field of outrigger canoe, surf ski & kayak paddlers. We have a 20km course around the Toronto Islands. The races are followed by a luau with delicious food and drink. All are welcome, including spectators!

For more information, see https://www.tioc.ca/